Jan 06, 2025

Deep Processing Unit Coagulation And Sedimentation Process in Wwtp

Leave a message

 

After secondary treatment of wastewater (biological treatment), sewage still contains a certain amount of pollutants, such as recalcitrant organic matter, nutrients such as nitrogen and phosphorus, trace amounts of heavy metals, and pathogens. The advanced processing unit coagulation and sedimentation process involves adding coagulants to wastewater to allow fine suspended particles and colloidal substances in the water to aggregate with each other, forming larger flocs. These flocs are then removed through sedimentation, effectively reducing suspended solids (SS) and some organic matter in the wastewater.

PAC wastewater

 

1. Coagulation reaction

The coagulation reaction requires the addition of chemical agents. Usually, when inorganic coagulants and organic coagulants are used simultaneously, inorganic coagulants should be added first. Commonly used ones include aluminum salts and iron salts (polyaluminum chloride PAC, polyferric sulfate PFS). These coagulants undergo hydrolysis reactions in water, forming positively charged colloids. For example, PAC will hydrolyze in water to form aluminum hydroxide colloids, whose colloidal particles carry a positive charge.

 

Suspended particles and colloidal impurities in wastewater usually carry negative charges. When positively charged colloids formed by coagulants enter wastewater, they will undergo charge neutralization with these negatively charged impurities. Just like the positive and negative poles of a magnet attract each other, neutralizing the charge of impurity particles.

 

The colloidal substances produced by the hydrolysis of coagulants can also connect multiple small suspended particles or colloids together through adsorption bridging. A coagulant colloidal molecule can simultaneously adsorb multiple impurity particles, forming a larger floc structure, which is beneficial for subsequent precipitation separation.

 

2. Operation control of coagulation reaction

To ensure the efficient progress of the coagulation reaction, it is necessary to strictly control the relevant parameters. Firstly, the dosage of coagulant should be determined based on the water quality, quantity, and concentration of pollutants in the wastewater. Generally, laboratory trials are conducted to simulate the coagulation effect under different dosages, in order to determine the optimal dosage. In textbooks, the molar ratio of adding coagulant to total phosphorus in wastewater should be 1.5-3, but it still needs to be determined based on the actual small-scale test situation on site.

Phosphorus removal molar ratio=(PAC concentration * treated water volume * 2/102)/(difference in total phosphorus concentration before and after treatment * treated water volume/31)

 

Molar ratio refers to the ratio of the amount of substances between two or more substances.

 

Secondly, the pH value of the reaction is also crucial, as different coagulants have their appropriate pH ranges. Taking PAC as an example, the optimal pH value of water is generally between 6.5-7.5. The coagulation effect will deteriorate if it is higher or lower than this range. In addition, the reaction time also needs to be controlled. Generally, the coagulation reaction time is around one to three to four minutes. If it is too short, it may lead to insufficient reaction, while if it is too long, it may cause the already formed flocs to disperse again.

 

3. Flocculation reaction

Due to the fact that the size of the flocs after coagulation cannot achieve the purpose of sinking by gravity, a coagulant aid is usually added during the coagulation stage. The coagulant aid itself generally does not have a coagulation effect, but mainly plays a role in assisting coagulation. Anionic polyacrylamide (PAM) is usually added. It is a high molecular weight polymer that, when added to wastewater, can adsorb onto the surface of already formed flocs, and through the bridging effect of long chains, further enlarge and compact the flocs.

 

For example, in some wastewater containing a large amount of fine colloids, the flocs formed by individual coagulation reactions are not strong and large enough. After adding polyacrylamide, its molecular chains can connect multiple flocs together like ropes, like a large net that holds many small particles together, forming visible large alum flowers, making the structure of the flocs more stable and conducive to precipitation.

 

After the drug is added, the small flocs that have already formed are mixed and combined with each other under hydraulic conditions using a slow stirring device. This process is like gently stirring many small alum flowers in water, allowing them to gradually stick together and form larger alum flowers.

 

The purpose of flocculation reaction is to further increase the size of flocs. The appropriate mixing speed and time are key factors. If the stirring speed is too fast, it will damage the already formed flocs; If the stirring speed is too slow or the time is not enough, the growth of flocs will not be sufficient. The stirring speed during the flocculation stage is roughly estimated to be around 30-60 revolutions per minute, and the reaction time is approximately 10-30 minutes, which needs to be adjusted according to the nature of the wastewater and treatment requirements.

frame agitator

 

For example, for sewage with high viscosity, it may be necessary to reduce the stirring speed appropriately to prevent the flocs from being damaged. At the same time, it is necessary to strictly control the flocculation reaction time to ensure that the flocs can fully grow. In addition, the dosage of coagulants also needs to be precisely controlled. Excessive coagulants may increase the viscosity of the water body, affecting the sedimentation effect; If it is too small, the ideal flocculation effect cannot be achieved.

 

4. Sludge sedimentation

The large flocs formed after flocculation reaction are precipitated in the sedimentation zone of the high-efficiency sedimentation tank by gravity. The settling velocity of particles in water is proportional to the square of the particle diameter and inversely proportional to the viscosity of water. Due to the large size of floc particles, their settling speed is relatively fast.

 

In order to improve sedimentation efficiency, the deep processing sedimentation unit usually adopts a inclined tube sedimentation device. The function of the inclined tube is to shorten the sedimentation distance of particles and increase the sedimentation area. When sewage flows in the inclined pipe, floc particles will slide down along the wall of the inclined pipe to the bottom. For example, in an inclined sedimentation tank, the inclination angle of the inclined pipe is generally around 60 degree. Sewage enters from the upper part of the inclined pipe and forms laminar flow inside the inclined pipe. The floc particles can settle to the mud collection area at the bottom of the inclined pipe in a relatively short time.

inclined tube settling tank

The sludge that settles to the bottom of the tank will be collected in the sludge hopper by the sludge scraper and discharged regularly. The supernatant after sedimentation flows out from the upper part of the sedimentation tank and enters the next processing unit or is directly discharged, thus achieving the separation of suspended solids and water.

 

Sludge discharge control should be carried out regularly and reasonably to avoid the accumulation of sludge at the bottom of the tank for a long time, which may cause sludge to float up and affect the effluent quality. The emission frequency and amount need to be determined based on the amount of sludge generated and the concentration of sludge. By installing a sludge concentration meter, real-time monitoring of sludge concentration can be achieved. When the sludge concentration reaches a certain threshold, timely discharge of sludge can be carried out. When discharging excess sludge, the sludge should be slowly discharged while observing the flow rate and concentration of the sludge discharge. During the discharge process, close attention should be paid to the water level changes in the sedimentation tank to prevent the water level from being too low due to rapid discharge, which may affect the sedimentation effect.

 

The sludge reflux ratio is one of the important parameters that affect the sedimentation efficiency of high-efficiency sedimentation tanks. Part of the sludge discharged from the sedimentation tank flows back to the front-end flocculation tank, which can utilize large particles as flocculation carriers and continue to release residual drugs. The appropriate sludge return ratio should be determined through experiments, generally controlled between 2% and 10%. Regularly conduct concentration testing on the returned sludge. If the concentration is too low, it indicates that the sedimentation effect of the sedimentation tank is poor and the dosage needs to be adjusted. The operation and maintenance of the inclined pipe regularly clean the sludge and debris on the surface of the inclined pipe to prevent sludge from accumulating on the surface of the inclined pipe and affecting the sedimentation effect. If accumulation is found, it may be due to delayed sludge discharge or poor sludge settling performance. It is necessary to adjust the dosing concentration and chemical ratio, and check whether there is a large amount of green algae growth causing blockage in the inclined pipe. The cleaning method can be hydraulic flushing or mechanical cleaning, and the cleaning frequency depends on the sludge accumulation on the surface of the inclined pipe. Regularly monitor the accumulation of sludge in blind spots to see if there is any floating or accumulation of sludge. If there is excessive accumulation, timely measures should be taken to deal with it, such as using mechanical stirring, hydraulic flushing, etc., to disperse the accumulated sludge and discharge it into the sedimentation tank.

sludge scraper

 

Regular inspection and maintenance should be carried out on relevant equipment in the sedimentation tank, such as sludge scraper, inclined pipe, etc. If the sludge scraper malfunctions, it may cause the sludge to be unable to be discharged in a timely manner, affecting the sedimentation effect; If the inclined pipe is blocked or damaged, it will reduce the sedimentation area and efficiency, and it needs to be cleaned and replaced in a timely manner.

 

Send Inquiry