The sludge in the biological treatment tank became fine and had poor settling properties, with numerous filamentous bacteria visible under a microscope. The total phosphorus (TP) in the effluent from the secondary settling tank exceeded the standard, even with a large dosage of downstream chemical phosphorus removal agents. The foam in the aerobic tank had an abnormal color, the sludge was whitish, and its activity was low. These problems often stem not from improper aeration or sludge age control, but from the microbial world. Maintaining a nutrient balance for microbial growth is fundamental to ensuring the stable and efficient operation of the biological treatment system.
Based on experience, the optimal nutrient ratio for the growth and reproduction of aerobic microorganisms is approximately BOD₅ : N : P = 100 : 5 : 1. Deviating from this ratio will cause various problems.
1. Insufficient Carbon Source
This is commonly seen in the following influent sources, particularly in industrial wastewater with a high proportion of industrial wastewater: such as chemical and pharmaceutical wastewater, which may have extremely low nitrogen and phosphorus content. Low-carbon, high-nitrogen-phosphorus municipal sewage: In some areas, domestic sewage has low organic matter concentrations due to water conservation measures. Subsequent rainwater or groundwater infiltration: This dilutes the organic matter in the raw water.
Consequences: Low nitrogen removal efficiency: Denitrification requires a carbon source as an electron donor. Insufficient carbon source prevents nitrate nitrogen (NO₃⁻-N) from being reduced to nitrogen gas, leading to excessive total nitrogen in the effluent. Deteriorated phosphorus removal efficiency: Polyphosphate-accumulating bacteria need to absorb readily degradable carbon sources (VFA) to release phosphorus during the anaerobic stage. Insufficient carbon source significantly reduces their subsequent aerobic phosphorus uptake capacity. Sludge aging: Microorganisms undergo endogenous respiration, leading to sludge mineralization, fragmented flocs, and poor settling performance.
2. Nitrogen Insufficiency
Treatment of high-carbon, low-nitrogen wastewater: Such as wastewater from food processing, brewing, and sugar refining, where the organic matter (BOD/COD) concentration is high, but nitrogen is relatively insufficient.
Consequences: Deterioration of sludge settling properties: When carbon is sufficient but nitrogen is insufficient, microorganisms synthesize excessive amounts of low-nitrogen polysaccharide colloidal substances, causing high-viscosity sludge bulking, increasing the SVI value, and making sludge-water separation difficult in the secondary settling tank. Decreased treatment efficiency: Microorganisms cannot effectively synthesize enzymes and proteins, their metabolism is hindered, and their ability to degrade organic matter decreases. Foaming problems: May promote the overgrowth of certain filamentous bacteria (such as microfilamentous bacteria), causing foaming problems.
3. Phosphorus Insufficiency
Relatively rare, but may occur in certain industrial wastewaters.
Consequences: Inhibited Microbial Activity: Phosphorus is crucial for energy conversion; phosphorus deficiency directly leads to reduced microbial activity and slowed metabolism. Poor Sludge Flocculation: Affects normal cell division, resulting in loose floc structure and turbid effluent.
On-site operation strategy
1. What carbon source should be chosen for supplementation?
Common choices: Sodium acetate (SD), methanol, glucose, etc.
Comparison: Sodium acetate reacts quickly and is often used in emergencies; methanol is cheaper but has biotoxicity and a slow start-up time; glucose is readily available but may cause filamentous bacteria bulking. Newer options: Utilizing volatile fatty acids (VFAs) produced from the fermentation of primary sludge or kitchen waste is a good method for resource utilization.
Where should it be added?
Primarily used for enhanced nitrogen removal, it is added at the front end of the anoxic tank.
Used for enhanced phosphorus removal, it is added at the front end of the anaerobic tank.
2. What nitrogen source should be chosen? Urea, ammonia, etc. Urea needs to be hydrolyzed into ammonia nitrogen by microorganisms before it can be utilized.
Where should it be added?
Usually added at the inlet of the anaerobic or anoxic tank to ensure that microorganisms can obtain sufficient nitrogen in the early stages of growth.
3. What phosphorus source should be chosen? Soluble phosphates such as phosphoric acid and sodium dihydrogen phosphate.
Where should it be added? Similar to the location for nitrogen source supplementation, it is added at the front end of the biological treatment tank.
