Apr 19, 2025

Design And Calculation Of Slaughter Wastewater Treatment Process

Leave a message

Determine the amount of wastewater

 

For example, the amount of wastewater generated from slaughtering a pig is generally about 0.4-0.7 tons, while the amount of wastewater generated from slaughtering a cow is about 1 ton, and the concentration of pollutants such as COD, BOD, SS in cow slaughtering wastewater can reach more than twice that of pig slaughtering wastewater. If a small slaughterhouse slaughters 200 pigs per day and generates 0.5 tons of wastewater per pig, then the daily amount of wastewater generated by pig slaughtering alone is about 100 tons. For example, in a large poultry slaughterhouse where 50000 chickens and ducks are slaughtered daily, it is estimated that the daily amount of wastewater generated from poultry slaughter is approximately 500-600 tons, based on the production of 1-1.2 tons of wastewater per hundred chickens and ducks.

2. Refer to industry norms and standards: For example, for designated pig slaughterhouses (sites), when using dry cleaning technology, the benchmark drainage volume per unit product is 0.5 cubic meters per head; When using the water flushing process, the benchmark discharge per unit product is 0.8 cubic meters per head. According to these specifications, we can accurately calculate the amount of wastewater generated based on the actual production process and output of the slaughterhouse.

In addition to the main methods mentioned above, there are also some factors that can affect the amount of slaughter wastewater generated:

3. Production process: Different slaughter production processes have significant differences in water consumption and wastewater generation. For example, using advanced water-saving slaughter equipment and processes such as dry blanching and high-pressure pulse flushing can effectively reduce water consumption and wastewater generation compared to traditional water flushing processes. Some modern slaughterhouses use closed circulating water systems to reuse some of the treated water for production, greatly reducing the use of fresh water and wastewater discharge.

4. Production habits: The production habits of slaughterhouses, such as the frequency and duration of floor washing, equipment cleaning methods, etc., can also affect the amount of wastewater. If the slaughterhouse washes the ground and equipment with water for a long time and in large quantities after production, the amount of wastewater generated will inevitably increase.

5. Seasonal factors: Seasonal changes also have a certain impact on the amount of slaughter wastewater produced. In summer, due to high temperatures, in order to maintain the cleanliness and hygiene of the slaughterhouse, there may be an increase in flushing frequency and water consumption, resulting in an increase in wastewater production; In winter, due to the possible impact of low temperatures on some water usage processes, the amount of water used may decrease.

 

Difficulty of treatment

 

1. The water quality is complex and diverse, containing not only high concentrations of organic matter such as proteins, fats, carbohydrates, but also inorganic pollutants such as ammonia nitrogen, total phosphorus, and total nitrogen. These pollutants interweave with each other, not only causing eutrophication of water bodies and excessive reproduction of algae, but also possibly causing water bodies to deteriorate and emit unpleasant odors, posing a serious threat to the surrounding environment and human health. For example, proteins in wastewater are decomposed by microorganisms, producing harmful substances such as ammonia nitrogen, which further exacerbates water pollution.

2. High concentration of pollutants and difficult treatment: The concentration of pollutants in slaughter wastewater is usually much higher than that in ordinary domestic sewage, and the concentrations of chemical oxygen demand (COD), biochemical oxygen demand (BOD), suspended solids (SS), ammonia nitrogen and other indicators are often several times or even dozens of times higher than those in domestic sewage. The COD concentration of wastewater from a large slaughterhouse is over 3000mg/L, while the COD concentration of general domestic wastewater is mostly between 300-500mg/L. The high concentration of pollutants greatly increases the difficulty of treatment, and conventional single treatment processes are difficult to achieve standard emissions.

3. Impurities are numerous and equipment is prone to clogging: The large amount of animal hair, meat residue, visceral debris, and other impurities in wastewater are the "enemy" of equipment operation. These impurities are prone to accumulate in pipelines, water pumps, grilles, and other equipment, causing equipment blockage and affecting the normal operation of the treatment system. In the actual processing, it is common for the grille to be tangled with hair and debris, resulting in poor water flow; The situation where the impeller of the water pump is stuck by impurities and damages the equipment. This not only requires frequent cleaning and maintenance of equipment, increasing labor costs and equipment wear and tear, but may also lead to interruptions in wastewater treatment, affecting production progress.

 

Slaughter wastewater treatment process

 

1. Preprocessing stage

(1) Grille slag removal: Through coarse and fine grids, larger solid impurities such as animal hair, bones, plastic bags, etc. can be effectively removed from wastewater, preventing these impurities from entering subsequent treatment equipment and causing equipment blockage.

(2) Sand settling tank: Using the principle of gravity settling, heavier particles such as sand in wastewater are precipitated. To avoid adverse effects on subsequent processing techniques. For example, after treatment in a sedimentation tank, the sand content in wastewater can be reduced by over 80%.

(3) Regulating pool: The function of a regulating pool is to regulate the amount and quality of wastewater, keeping it stable within a certain range. By regulating the homogenization of the regulating pool, the stable operation of subsequent processing units can be ensured. For example, a slaughterhouse controlled the pH fluctuation range of wastewater within ± 0.5 through regulating tanks, and the impact of water quality fluctuations on treatment efficiency was significantly reduced.

2. Main processing stage

(1) Aerobic biological treatment: With the help of aerobic microorganisms, organic matter in wastewater is decomposed into harmless substances such as carbon dioxide and water. Common aerobic treatment methods include activated sludge process, biofilm process, etc. Taking the activated sludge process as an example, in the aeration tank, aerobic microorganisms in the activated sludge come into full contact with the wastewater, utilizing the organic matter in the wastewater as nutrients for growth and reproduction, thereby achieving the degradation of organic matter. A company that uses activated sludge method to treat slaughter wastewater has a COD removal rate of over 80%.

(2) Anaerobic biological treatment: For high concentration slaughter wastewater, anaerobic biological treatment is an effective means. It utilizes anaerobic microorganisms to decompose large molecular organic matter in wastewater into small molecular organic matter under anaerobic conditions, while generating renewable energy such as biogas. The upflow anaerobic sludge bed (UASB) reactor is a commonly used anaerobic treatment equipment, and its internal anaerobic sludge bed can efficiently degrade organic matter. In a certain slaughter wastewater treatment project, UASB reactor is used for anaerobic treatment, and the COD removal rate of the wastewater can reach about 70%. At the same time, the daily generated biogas can meet the energy demand of some plant areas.

(3) Air flotation treatment: Using the principle of air flotation, suspended solids and some oils in wastewater are attached to tiny bubbles, thereby achieving separation from water and improving the clarity of wastewater. By introducing air or other gases into the wastewater, tiny bubbles are formed. These bubbles combine with suspended solids and oils in the wastewater, floating to the surface to form floating slag, which is then removed by a scraping device. After adopting the air flotation treatment process, the removal rate of suspended solids in the wastewater of a certain slaughterhouse can reach over 90%, and the removal rate of oil and fat can reach over 85%.

Send Inquiry